Unique Free Articles. Free submission.
Search:

Unique Free Article:
'Water-Based Finishes: What Should You Know About Them?'

Article Source: http://www.unique-free-articles.com


Megan Cherry writes for www.pegandrail.com If you are looking for a high quality well made coat rack step in and check us out, we manufacture a complete line of wall mounted coat rack from a www.pegandrail.com/'>Shaker peg style coat rack to a modern wall www.pegandrail.com/wall-coat-hooks.html'> coat hooks with brass hooks or satin nickel for the brushed stainless steel look we even have a very modern looking hand rub white lacquer coat racks.




"....Therefore, you know that the fumes can be quite intense, especially in an enclosed space.....
.........."


"..... However, water-based finishes still use some of the same resins used in urethane and acrylic finishes. Therefore, you know that the fumes can be quite intense, especially in an enclosed space.....
.........."

It's true that in take on trust water-based finishes are safer than other finishes, and that they are also safer to handle. Most of you have used latex paint before. Water-based finishes are indeed much safer than traditional lacquers, but you should still be careful when you use them. This is also true for water-based finishes, and you'll want to take proper precautions to protect both your skin and lungs. Therefore, you know that the fumes can be quite intense, especially in an enclosed space. The resins are not mixed with water, though, so they have to be chemically modified in order to be emulsified with the water. Make sure there's adequate ventilation, wear proper protective clothing, and wear a respirator as well.

Many harmful additives have been replaced by water in these types of finishes. Try this sometime. These want chemicals called surfaces and solvents to be added; in the crowd these are glycol ethers, which force resins to mix with water.

Yet another problem with water-based finishes is that the water will oftentimes raise the grain in the wood. You'll notice that the wood fibers will absorb the water and swell, which makes them 'stand up' and roughen. Sand a piece of wood and then rub some neat water on it. This will add a barrier amongst the wood and the next coat of finish. To get on all sides this problem, you can use a seal or coat of shellac. Alternatively, you can use a couple of sublimated coats of standing sealer. It will also give your wood a little bit of an amber color. Other lacquers might cause a slight amber color to the wood. Once the standing sealer has dried, you can lightly sand the wood, which will even it out.

Fortunately, though, water finishes are of a irresolute color, which stock that they don't add any color to the wood as other finishes might. However, there are certain woods that do not do best with a water-based finish. Therefore, if you want to keep your wood's natural color without any malformation whatsoever, a water-based finish is a Herculean choice. If a water-based finish is applied, this tends to 'tone down' the color of the wood so that the profound rich wood color is somewhat negated with a water-based finish.

Therefore, water-based finishes have both pros and cons. These are the darker woods such as cherry or walnut. In addition, water-based finishes have much below the mark of an odor and clean up is much easier than it is with other types of finishes. Pros are that they are not flammable and are underADJ Expensiveness polluting than traditional finishes are, they don't yellow, dry expeditious and can be either sprayed on or applied with a brush. Most cannot give wood a deep, rich color as we are used to with a solvent-based finish. However, they have drawbacks too. For example, steel wool will rust quickly with water-based finishes, and natural bristle brushes will absorb too much water and become limp. In addition, the water raises the wood's grain and can be very laborious to apply, since humidity and temperature execute a role in both application and drying times.

In addition, with water-based finishes, the tools you'll need will be slightly out of ones element than those with solvent-based finishes. In addition, if you're using either a conventional or high-volume low-pressure spray gun, you'll need to have stainless steel needles and nozzles so that corrosion does not happen.

"........'

Additional Articles From - Home | Misc Articles
  • Ayurveda NYC ~ Healthy Life with Oldest Medical Systems the Ayurveda NYC ~ Ayurveda Day Spa New York - By : sworna ambika
  • NIO Teapot by Oliver Hemming ~ Stainless steel beautiful teapot ~ Oliver Hemming teapot - By : jeya lakshmi
  • gps & gis ~ Multimedia Projectors - VA Store ~ handheld gps - By : Ibrahim Machiwala
  • American Idol ~ My Dream Come True: From Chicken Soup For The American Idol Soul ~ Scott Savol - By : iSnare Articles
  • Shopping ~ Salir de Compras: Terapia Anti Stress ~ Health - By : Mia Pacheco
  • reminders and alerts ~ reminders and alerts ~ Reminders And Alerts Are A Must For Businesses ~ sms messaging services ~ sms messaging services - By : iSnare Articles
  • electronic statement delivery ~ electronic statement delivery ~ Creating A Paperless Business Is Possible ~ Premiere Global Services ~ Premiere Global Services - By : iSnare Articles
  • budget conferencing ~ budget conferencing ~ Conference Calls Do Not Have To Be Costly ~ conference for web ~ conference for web - By : iSnare Articles
  • budget conferencing ~ budget conferencing ~ Conference Calls: The Basic Do‘s And Don‘ts ~ conference for web ~ conference for web - By : iSnare Articles
  • Using Hat Rack Seat Mounts For Added Versatility - By : iSnare Articles


  • RSS XML Search N Find Articles
    Click the XML Icon Above to Receive Misc Articles Articles Via our RSS system!

    Water-Based Finishes: What Should You Know About Them?


    Partners

    Powered by Article Dashboard